The details for both Toyota Land Cruiser and Sequoia are similar.
How to replace Automatic Transmission on Toyota car models,The procedure for this is as follows :---
Transmission Removal & Installation Step by step Instructions are as follows :----
Transmission and related parts-Sequoia
Car repair guide?
http://technoanswers.blogspot.in/2012/03/car-repair-guide.html
How to replace Automatic Transmission on Toyota car models,The procedure for this is as follows :---
Transmission Removal & Installation Step by step Instructions are as follows :----
- Remove or disconnect the following:
Oil filler pipe
No. 1 engine undercover
Exhaust pipes
Front and rear driveshafts
Nos. 1&2 vehicle speed sensors
Solenoid connector
Shift cable at the transmission
Overdrive sensor connector
Oil cooler lines
ATF temperature sensor
Park/Neutral switch
End plate and converter clutch mounting bolts
- Raise the transmission slightly.
- Remove or disconnect the following:
Crossmember
Rear mount insulator
Transmission and transfer case as a unit
- Installation is the reverse of removal. Note the following torques:
Transmission-to-transfer case bolts: 53 ft. lbs. (71Nm)
Rear mount insulator-to-transmission: 48 ft. lbs. (65Nm)
Rear mount insulator-to-crossmember: 13 ft. lbs. (18Nm)
Crossmember-to-frame: 53 ft. lbs. (71Nm)
Torque converter clutch: 30 ft. lbs. (41Nm)
Transmission and related parts-Sequoia
NOTE
Install the green bolt first.
Rear end plate: 13 ft. lbs. (18Nm)
Oil cooler lines: 25 ft. lbs. (34Nm)
Shift control bracket: 13 ft. lbs. (18Nm)
Oil cooler lines: 25 ft. lbs. (34Nm)
Shift control bracket: 13 ft. lbs. (18Nm)
Fig. Transmission and related parts-Land Cruiser
- Before servicing the vehicle, refer to the Precautions section.
- Remove or disconnect the following:
Battery and tray
Air intake assembly
Cooling fan and shroud
Coolant recovery reservoir
Transmission dipstick tube
Center console
Transmission gear select lever and rod
Transfer case shift lever and rod
Engine under covers
Exhaust front pipes
Front and rear driveshafts
Vehicle Speed (VSS) sensor connectors
Overdrive clutch speed sensor connector
Solenoid harness connector
Transmission fluid temperature sensor connector
Park/Neutral Position (PNP) switch connector
Center differential lock indicator switch connector
L4 solenoid valve position switch connector
Motor actuator connector
Torque converter
Transmission oil cooler lines
Transmission mount crossmember. Support the transmission with a jack.
Transmission flange bolts
Transmission
To install:
- Install or connect the following:
Transmission. Tighten the flange bolts to 53 ft. lbs. (72 Nm).
Transmission mount crossmember. Tighten the bolts to 37 ft. lbs. (50 Nm) and the nuts to 54 ft. lbs. (74 Nm).
Transmission oil cooler lines
Torque converter. Tighten the bolts to 35 ft. lbs. (48 Nm).
Motor actuator connector
L4 solenoid valve position switch connector
Center differential lock indicator switch connector
PNP switch connector
Transmission fluid temperature sensor connector
Solenoid harness connector
Overdrive clutch speed sensor connector
VSS sensor connectors
Front driveshaft. Tighten the fasteners to 59 ft. lbs. (80 Nm).
Rear driveshaft. Tighten the fasteners to 78 ft. lbs. (106 Nm).
Exhaust front pipes
Engine under covers
Transfer case shift lever and rod
Transmission gear select lever and rod
Center console
Transmission dipstick tube
Coolant recovery reservoir
Cooling fan and shroud
Air intake assembly
Battery and tray
- Check the transmission and transfer case fluid levels and adjust as necessary.
These details will help.
Thanks.
FOR MORE HELP GO TO: ---
No comments:
Post a Comment